Contents15
- Two links between the basement and your phone
- Picks by situation
- Sensor for a dry room or floor
- Hub for Tapo sensors
- How many sensors, and what the setups cost
- Basement humidity targets and alerts
- Waterproofing, cold and batteries
- History, calibration and checking a dehumidifier
- FAQ
- What humidity should a basement stay under?
- How can I check my basement humidity from upstairs?
- Does Bluetooth reach through a floor or a concrete wall?
- Where should I put the hub?
- Does a basement hygrometer need to be waterproof?
- How do I tell whether my dehumidifier is working?
Keep basement humidity below 60% if possible, ideally 30-50% (EPA), and no higher than 50% according to CDC. To check it from upstairs, use a hub and test that both the sensor-to-hub and hub-to-router links reach.
This guide uses official specs and Amazon.com listings as of October 2026. Nothing was tested on real devices.
Two links between the basement and your phone
According to SwitchBot’s official guidance, without a hub, a SwitchBot hygrometer can only be viewed within Bluetooth range of the phone. To see a basement from upstairs through a hub, the Bluetooth link from sensor to hub and the Wi-Fi link from hub to router must both reach. The hub supports 2.4 GHz Wi-Fi only.
As of October 2026, according to SwitchBot, the US page for the Outdoor Meter lists a Bluetooth range of 394 ft (about 120 m) with no obstacles. A figure for crossing a floor or a concrete wall wasn’t found, so check reception in your own home.
Put the hub where both the sensor and the router reach, and where you can power it. How to find that spot is in the steps below. The Hub 2 is powered by USB-C (5V/2A); the Tapo H100’s power was not checked.
Test the setup in this order:
- Pick two powered spots for the hub: one near the sensor and one near the router.
- With SwitchBot, carry your phone to each spot and check that the sensor’s reading shows in the app. With Tapo, pair the hub first, then check the same.
- With the hub connected, turn off your phone’s Wi-Fi and Bluetooth, open the app on cellular and check that the reading and update time are recent.
- If nothing arrives, check whether the hub is online to test the router side, and whether the sensor’s reading updates to test the sensor side. Try the other spot. If both fail, rethink the placement.
Picks by situation
For a spot that may get splashed or damp, the SwitchBot Outdoor Meter (waterproof) with the SwitchBot Hub 2 is the pick. For a dry room or floor on a budget, the Tapo T310 with the Tapo Hub H100 is the pick, with the checks noted below.
- Sensor for a spot that may get splashed: SwitchBot Outdoor Meter (waterproof)
A thermo-hygrometer SwitchBot lists as waterproof (IP65). That rating covers dust and water jets, not condensation. Its humidity accuracy is ±1.8 %RH, and with a hub you can check it from another floor.
Sold by SwitchBot US. The rating count is combined with other listings of the same sensor.
- Hub to relay the sensor: SwitchBot Hub 2
A relay hub for SwitchBot sensors, with its own sensor built in, so placed upstairs it doubles as the upstairs reference. SwitchBot’s US Outdoor Meter page says the Hub 2 screen can show that sensor’s readings (a search summary); the US Hub Mini Matter device list omits the Meter series. It needs 2.4 GHz Wi-Fi and USB-C power (5V/2A).
The rating count may be combined with other listings.
Sensor for a dry room or floor
A Tapo sensor that pairs with the H100 hub. Tapo’s US page for the T315 in the same line lists ±3 %RH accuracy and a required hub. The T310’s own US spec page, its operating range and its water resistance were not checked, so confirm them before using it in a damp spot.
Hub for Tapo sensors
Its power, mounting and box contents were not checked. Confirm them on the official page.
How many sensors, and what the setups cost
Plan on one sensor per spot you want to watch, plus one upstairs as a reference. Three spots and one reference make 4.
| Spot | Setup | Sensors (3 spots plus an upstairs reference) |
|---|---|---|
| May get splashed or damp | Waterproof (IP65) sensors and a relay hub | 4 |
| Dry room or floor | Hub-required sensors and their hub | 4 |
Which basement sensor setup do I need?
Pick the kind of spot, how many spots, and whether you want an upstairs reference. It shows the matching setup and how many sensors.
For these settings
For these settings
For these settings
For these settings
On price alone, for any of 1 to 4 sensors, the Tapo setup costs less than the SwitchBot setup. Reception, water resistance and condensation handling are not in the price.
Basement humidity targets and alerts
EPA says to keep indoor humidity below 60% if possible, ideally 30-50%, and CDC says no higher than 50%. Both are stated for indoor air in a home.
As of October 17, 2026, on the pages checked, no basement-only humidity figure was found, so this guide applies the same indoor line to a basement.
According to EPA’s pages, uninsulated concrete floors are often colder than the basement air, so moisture can condense on the slab and promote mold growth in carpet. EPA also says the basement belongs in the home’s ventilation plan.
CDC says humidity changes through the day, so check more than once a day, and suggests considering not using carpet in places like bathrooms or basements.
SwitchBot says push notifications need a hub. Tapo’s US page for its T315 sensor lists an app alert when readings leave a preset range, and says the Tapo hub is required for smart features. Without a hub, don’t count on alerts.
Taking the rated accuracy as ±1.8 to 3 %RH, a calculated alert setting is 56% on the display. That is the 60% line minus 3 points of accuracy and 0.5 point for rounding, and for CDC’s 50% line it is 46%. Whether an alert fires at the setting or only above it was not checked on a real unit.
Waterproofing, cold and batteries
Among the SwitchBot sensors checked, only the Outdoor Meter is listed as waterproof (IP65). Its operating range is -20 to 60 °C, or -4 to 140 °F, which covers the assumed winter low of 0 to 15 °C, or 32 to 59 °F. Whether it may sit where condensation forms was not confirmed.
The SwitchBot Outdoor Meter takes 2 AAA batteries with a rated life of up to 2 years. A figure for battery life in the cold wasn’t found.
History, calibration and checking a dehumidifier
According to SwitchBot’s official guidance, the Outdoor Meter keeps 68 days on the device. With a hub, the cloud keeps up to 2 years. A link outage of up to 30 days (an assumption) fits in the on-device record, but whether the outage’s readings reach the cloud afterward wasn’t found in the official pages.
According to Tapo’s official guidance, earlier data may be lost if the hub is offline for about 24 hours or more. Every outage in the assumed range (1 to 30 days) is at least that long. No on-device record was found in Tapo’s pages.
SwitchBot says app history can be exported as CSV. Tapo keeps the most recent two calendar years and emails a CSV, and Govee also sends a CSV by email.
The Meter Pro can be calibrated in the app, and SwitchBot warns that calibrating to an inaccurate reference can be worse than not calibrating. A saturated salt solution gives about 75.3% RH at 25 °C (77 °F), but Boveda says a homemade salt test is not precise. Try it at room temperature, not in a cold basement.
To see whether a dehumidifier helped, compare the history graph before and after, not a single reading.
FAQ
What humidity should a basement stay under?
EPA says indoor humidity should be below 60% if possible (ideally 30-50%), and CDC says no higher than 50%; no basement-only figure was found.
How can I check my basement humidity from upstairs?
To view from upstairs, the Bluetooth link from sensor to hub and the Wi-Fi link from hub to router must both reach.
Does Bluetooth reach through a floor or a concrete wall?
A figure for Bluetooth through floors or concrete walls wasn’t found in the pages checked, so test it in your own home.
Where should I put the hub?
Try the hub near the sensor and near the router, and keep it where both reach and where you can power it. Check the hub’s power requirement on its official page.
Does a basement hygrometer need to be waterproof?
Only where water may reach it, since a sensor listed as waterproof (IP65) covers splashes, but condensation was not confirmed.
How do I tell whether my dehumidifier is working?
A single reading can’t show it. Compare the history graph from before and after you turned it on.
Data and formulas used (for verification)
Related guides:
- Check Room Humidity While Away: You Need Wi-Fi or a Hub
- Closet Hygrometer: Is a Plain One Enough, or Go Smart?
- Is it OK to put a humidifier near a computer?
How this was checked: On Amazon.com as of October 17, 2026, the picks have 100 or more ratings and 4.0 stars or more, and are sold by Amazon.com or a brand-named seller. Delivery was set to ZIP 10001, and rating counts may include other listings or models of the same product; check the price on the store page. The assumptions and data used are in “Data and formulas used” at the end.
Method
- Covers Amazon.com listings (delivery to ZIP 10001) as of 2026-10-17 and official specs from SwitchBot, Tapo and Govee. Nothing was tested on real units.
- The EPA and CDC figures used (EPA: below 60% if possible, ideally 30-50%; CDC: no higher than 50%) are stated for indoor air in a home. No basement-only figure was found on the EPA pages checked; this guide applies the same line to a basement.
- Bluetooth range is the 394 ft (about 120 m) that SwitchBot’s US Outdoor Meter page lists with no obstacles; the Meter’s US page also lists 394 ft. No official figure for floors or concrete walls was found. Hub placement assumes you check, in your own home, a spot both links reach.
- How many spots, whether to add an upstairs reference, the winter low and the days the sensor-to-hub link stays down are assumptions, checked across a range. Sensors = spots + the upstairs reference.
- Operating temperatures: Outdoor Meter -20 to 60 °C (-4 to 140 °F), Meter -10 to 60 °C (14 to 140 °F) (SwitchBot material, search summary). Only the Outdoor Meter’s IP65 rating was confirmed as waterproof. The Tapo T310’s own US spec page was not fetched, so its operating range and water resistance are not stated; Tapo details come from the T315 US page and Tapo US FAQs.
- The calculated alert setting is floor(60 - 3 - 0.5) = 56. 60 is the line, 3 is the humidity accuracy (+/- %RH) and 0.5 is the whole-number display allowance. Accuracy is a rated value, not tested.
- Cost is sensors x unit price + the hub price (Amazon.com prices on 2026-10-17). Reception, water resistance and condensation handling are not in the price. How many sensors one SwitchBot or Tapo hub can connect was not checked on US pages.
- The 75.3% RH of a saturated salt solution is a 25 C value and changes with temperature; Boveda says a homemade salt test is not precise.
- Sources by market: SwitchBot US pages (switch-bot.com) for the Outdoor Meter, Meter and Hub 2; Tapo US pages (tapo.com/us, tp-link.com/us FAQ) for the T315 and hubs. The Hub 2 relay support for the Outdoor Meter and the Hub 2 power come from search summaries of US pages. Where a SwitchBot statement comes from a switchbot.jp page, the table’s source column shows it.
- The Meter’s on-device record is 36 days in a SwitchBot support article and 68 days on its US product page, so the Meter is left out; the Outdoor Meter’s 68 days is stated by both.
- Rating counts on Amazon may include other listings or models of the same product, so they are a rough guide.
Assumptions
- How many spots you want to watch (a basement’s outer-wall corner and middle, a crawl-space storage, a room on another floor), held as a 1-3 range (an assumption of this article).: 2 (1–3)
- Whether to put one reference sensor upstairs near the hub (0-1). This guide’s own arrangement, not an official instruction.: 1 (0–1)
- Winter low (C) of an unheated basement or storage space. An assumption, not an official figure; held as 0-15 C to compare with each sensor’s operating minimum.: 5 (0–15)
- Humidity accuracy (+/- %RH). Rated figures: SwitchBot Meter and Outdoor Meter 1.8 (US page), Meter Pro 2, Tapo 3, Govee H5179 3. Rated under stated conditions, not tested; the alert calculation uses the safer 3.: 3 (1.8–3)
- Days the sensor-to-hub link stays down (dead battery, no signal). An assumption, not an official figure; held as 1-30 days.: 7 (1–30)
Official values used
| Item | Value | Source | Checked |
|---|---|---|---|
| epa_humidity_30_50 | EPA: if possible, keep indoor relative humidity below 60 percent (ideally 30-50 percent); it can be measured with a small, inexpensive ($10-$50) humidity meter. | epa.gov If possible, keep indoor humidity below 60 percent (ideally between 30 and 50 pe | 2026-10-17 |
| cdc_humidity_50 | CDC: keep humidity in the home as low as you can, no higher than 50%, all day long; humidity changes over the course of a day, so check more than once a day; consider not using carpet in places like bathrooms or basements. | cdc.gov Keep humidity levels in your home as low as you can–no higher than 50%–all day | 2026-10-17 |
| epa_basement_condensation | EPA: damp basements promote biological growth including molds; uninsulated concrete slabs are often colder than the basement air, so moisture can condense on the slab and promote mold growth in carpet; the basement should be part of the home’s ventilation strategy. | epa.gov Because damp basements promote biological growth, including molds, they are not | 2026-10-17 |
| epa_condensation_cold_surface | EPA: high humidity (60% RH) is a common moisture problem; when warm, humid air contacts a cold surface, condensation may form; mold is frequently found on walls in cold corners behind furniture. | epa.gov When warm, humid air contacts a cold surface, condensation may form. / Mold is f | 2026-10-17 |
| switchbot_meter_remote_needs_hub | SwitchBot says Meter-series sensors can only be viewed within Bluetooth range without a hub; remote viewing and phone push notifications need a SwitchBot hub. | switchbot.jp | 2026-10-17 |
| switchbot_meter_cloud_history_2y | SwitchBot states up to two years of data can be stored in the cloud when a Meter is used with a hub (the US product page also says unlimited cloud storage). | support.switch-bot.com | 2026-10-17 |
| switchbot_meter_onboard_days | Official on-board storage: 68 days for Meter Plus, Outdoor Meter and Meter Pro; 36 days for Meter and Meter Pro CO2 per support article (the US Meter product page says 68 days). | support.switch-bot.com | 2026-10-17 |
| switchbot_meter_export_csv | SwitchBot says Meter-series data can be exported as CSV from the app. | switch-bot.com Data exportable as CSV. | 2026-10-17 |
| switchbot_meter_bt_range_394ft | SwitchBot US pages list Meter/Meter Plus at 394 ft (~120 m); the Outdoor page adds ‘no obstacles’. | switch-bot.com View temperature and humidity data from 394ft away. | 2026-10-17 |
| switchbot_meter_pro_calibration | SwitchBot says Meter Pro can be calibrated in the app (Settings → Calibration), temperature and humidity separately, and warns that calibrating to an inaccurate reference can be worse than not calibrating. | support.switch-bot.com | 2026-10-17 |
| switchbot_hub2_wifi_24ghz | SwitchBot Hub 2 supports 2.4 GHz Wi-Fi only (no 5 GHz). | switchbot.jp | 2026-10-17 |
| switchbot_hub3_bluetooth_devices | SwitchBot says the universal remote hubs manage up to 15 Bluetooth devices (12 SwitchBot devices + 3 Bluetooth remotes). | support.switch-bot.com | 2026-10-17 |
| switchbot_hub2_sensor_accuracy | SwitchBot Hub 2 accuracy is shown as +/-1.8% RH / 0.36 F on the US page and +/-0.2 C (0-65 C), +/-2% RH (10-90%) in Japanese material. | switch-bot.com accuracy up to ±1.8% RH/±0.36°F | 2026-10-17 |
| govee_h5075_remote_bt_only | Govee H5075 supports Bluetooth only, no Wi-Fi. Govee’s page does not say a gateway is needed or supported for remote viewing. | us.govee.com No. The product only supports Bluetooth connection. | 2026-10-17 |
| govee_h5179_wifi_direct | Govee H5179 connects over 2.4GHz Wi-Fi without a gateway; 5GHz is not supported. | us.govee.com No. It only works with 2.4GHz Wi-Fi. | 2026-10-17 |
| govee_3lite_gateway_required_for_alerts | Govee’s 3 Lite page says app alerts require the Wi-Fi gateway + sensors version; the gateway is not sold alone and pairs with up to 30 sensors. | us.govee.com please must purchase a Wi-Fi gateway+sensors version, wifi gateway is not sold a | 2026-10-17 |
| govee_h5179_history_20d_2y | Govee H5179 page: 20 days of online storage to view and export, up to 2 years of data. | us.govee.com Enjoy 20 days of online data storage view and export up to 2 years’ worth of dat | 2026-10-17 |
| govee_export_csv_email | Govee exports history as CSV to your mailbox (account login required for H5075; email address entered for H5179). | manualslib.tech Send historical data to your mailbox in CSV format. | 2026-10-17 |
| govee_h5075_bt_range | Govee H5075 Bluetooth range: manual says 50m with no obstacles; US page lists both 60m and 50m (open, unobstructed). No official 80m figure found. | manualslib.tech 50m/164ft (NO obstacles) | 2026-10-17 |
| govee_h5179_bt_wifi_range | Govee H5179: Bluetooth 30m and Wi-Fi 50m, both with no obstructions. | manualslib.tech 30m/49ft (no obstructions) / Wi-Fi range 50m/98ft (no obstructions) | 2026-10-17 |
| govee_h5075_calibration | Govee H5075 calibration range per manual: 3°C for temperature, 20.0% for humidity. | manualslib.tech Calibration range for the temperature is 3ºC/5.4ºF while for the humidity is 20. | 2026-10-17 |
| govee_alert_conditions | Govee sends push alerts when readings leave the preset range; no frequency limit documented. For H5179, delayed alerts are attributed to Wi-Fi stability. | manualslib.tech Cannot receive alerts / alerts delayed: Make sure Wi-Fi signal is stable. | 2026-10-17 |
| govee_onboard_log_unconfirmed | No official Govee page or manual found that documents onboard storage days or sync after reconnecting. | us.govee.com | 2026-10-17 |
| govee_h5179_goveelife_migration | Search summary says Govee UK/CA/US H5179 pages carry a notice about moving appliances to GoveeLife sites; no explicit model discontinuation. | uk.govee.com | 2026-10-17 |
| inkbird_th2plus_onboard_bt | Inkbird IBS-TH2 Plus stores up to 30,000 points on the device; Bluetooth 98ft without obstacles; remote use needs a gateway such as IBS-M2. | inkbird.com stores a maximum of 30,000 points of data on the device. | 2026-10-17 |
| inkbird_m2_gateway | Inkbird IBS-M2: 2.4GHz Wi-Fi, up to 9 Bluetooth sensors, 1-year history, alarm notifications, 164ft Bluetooth without interference. | inkbird.com Maximum Number of Devices Supported: 9 | 2026-10-17 |
| inkbird_th3plus_history_csv | Inkbird IBS-TH3 WIFI PLUS: Wi-Fi direct (2.4GHz), 1-year history, CSV export, calibration ±10, rechargeable ~3 months at 60-min interval. | inkbird.com View historical data of the past year. | 2026-10-17 |
| thermopro_tp357_bt_range | ThermoPro TP357 rated Bluetooth range is 260 ft (80 m) in open space with no obstructions or interference. | temppro.com stable, reliable range of up to 260 feet (80 meters) in open spaces. | 2026-10-17 |
| thermopro_tp357_history_1y | ThermoPro TP357 shows 1 year of history; 2-year exportable data is attributed to TP350/TP358. | temppro.com 1-year data storage with an easy-to-use graph feature. | 2026-10-17 |
| thermopro_tp371_wifi_remote | ThermoPro TP371: 2.4GHz Wi-Fi + Bluetooth, no gateway, remote over internet, up to 2 years exportable CSV; shown sold out. | temppro.com Remote Range: No distance limit over Wi-Fi. | 2026-10-17 |
| tapo_t31x_history_2years | Tapo sensors retain history for the most recent 2 calendar years; export to CSV via email from the app | tp-link.com The sensor retains historical data from the most recent 2 calendar years. | 2026-10-17 |
| tapo_hub_offline_data | Tapo: if the hub is offline more than ~24 hours earlier data may be lost; rebooting the hub deletes unuploaded history; power-outage data is lost | tp-link.com If the hub remains offline for more than about 24 hours, it may lose earlier dat | 2026-10-17 |
| tapo_hub_history_delete | Tapo: removing the sensor or hub from the app deletes history permanently; H100 10-second factory reset deletes it, 5-second soft reset keeps it | tp-link.com Deleted historical data cannot be recovered. | 2026-10-17 |
| boveda_salt_test_caveat | Boveda says a homemade salt test cannot give a precise RH value; it varies with salt-to-water ratio | help.bovedainc.com You’ll never receive a precise relative humidity (RH) reading | 2026-10-17 |
| salt_75_nacl | Saturated NaCl gives ~75.3% RH at 25°C (Greenspan); sealed chamber, ~24h equilibration; stated uncertainty 1.4% RH + Greenspan | engineering.purdue.edu | 2026-10-17 |
| switchbot_hubmini_setup | SwitchBot says the original Hub Mini is powered by 5V 1A/2A USB and supports 2.4 GHz Wi-Fi only (no 5 GHz). What is in the box (adapter, cable) could not be confirmed on the official product page. | switch-bot.com | 2026-10-17 |
| switchbot_hub2_power_us | SwitchBot Hub 2 is powered by USB-C (5V/2A) and supports 2.4 GHz Wi-Fi only (read as a search summary). What is in the box was not confirmed. | switch-bot.com | 2026-10-17 |
| switchbot_hub2_relays_indoor_outdoor_us | SwitchBot’s US page for its Indoor/Outdoor Thermo-Hygrometer (the Outdoor Meter) says the Hub 2 screen can display that sensor’s temperature and humidity, with a flashing screen and sound alert (read as a search summary). The Hub 2 US page was not checked for the Meter itself. | switch-bot.com | 2026-10-17 |
| switchbot_hub_mini_us_meter_unconfirmed | The US SwitchBot Hub Mini page has no text on working with the Meter, and the US Hub Mini Matter page’s device list does not name the Meter series. | switch-bot.com | 2026-10-17 |
| switchbot_outdoor_battery_range_us | SwitchBot’s Outdoor Meter (US name: Indoor/Outdoor Thermo-Hygrometer): 2 AAA batteries, up to two years of battery life (US page), operating range -20 to 60 °C (SwitchBot Japan page, read as a search summary). The Meter’s -10 to 60 °C is from a SwitchBot compliance article (search summary). | switch-bot.com up to two years | 2026-10-17 |
| tapo_t315_us_page | Tapo’s US T315 page: accuracy ±3% RH; the Tapo Hub is required for smart features, remote monitoring and data export; app alert when readings leave a preset range. The T310’s own US spec page was not fetched. | tapo.com Measurement Accuracy: ±0.54 ºF, ±3% RH / Hub Required / Receive app alert notifi | 2026-10-17 |
Which basement sensor setup do I need?: quick reference
The calculator in this article shows the result and a matching product for your own settings. Settings can be set in the URL; each link below opens the calculator with those settings.
| Settings | Result | Calculator |
|---|---|---|
| May get splashed or damp, 1 spot, Add a reference | ✓ Pick: the waterproof sensor and hub setup. 1 waterproof sensor (one per spot) and one hub with a built-in sensor placed upstairs as the reference: 2 sensors in all. A thermo-hygrometer SwitchBot lists as waterproof (IP65). That rating covers dust and water jets, not condensation. Its humidity accuracy is ±1.8 %RH, and with a hub you can check it from another floor. A relay hub for SwitchBot sensors, with its own sensor built in, so placed upstairs it doubles as the upstairs reference. SwitchBot’s US Outdoor Meter page says the Hub 2 screen can show that sensor’s readings (a search summary); the US Hub Mini Matter device list omits the Meter series. It needs 2.4 GHz Wi-Fi and USB-C power (5V/2A). On price alone Tapo’s setup costs less, but water resistance and condensation handling are not in the price | Open with these settings |
| May get splashed or damp, 2 spots, Add a reference | ✓ Pick: the waterproof sensor and hub setup. 2 waterproof sensors (one per spot) and one hub with a built-in sensor placed upstairs as the reference: 3 sensors in all. A thermo-hygrometer SwitchBot lists as waterproof (IP65). That rating covers dust and water jets, not condensation. Its humidity accuracy is ±1.8 %RH, and with a hub you can check it from another floor. A relay hub for SwitchBot sensors, with its own sensor built in, so placed upstairs it doubles as the upstairs reference. SwitchBot’s US Outdoor Meter page says the Hub 2 screen can show that sensor’s readings (a search summary); the US Hub Mini Matter device list omits the Meter series. It needs 2.4 GHz Wi-Fi and USB-C power (5V/2A). On price alone Tapo’s setup costs less, but water resistance and condensation handling are not in the price | Open with these settings |
| May get splashed or damp, 3 spots, Add a reference | ✓ Pick: the waterproof sensor and hub setup. 3 waterproof sensors (one per spot) and one hub with a built-in sensor placed upstairs as the reference: 4 sensors in all. A thermo-hygrometer SwitchBot lists as waterproof (IP65). That rating covers dust and water jets, not condensation. Its humidity accuracy is ±1.8 %RH, and with a hub you can check it from another floor. A relay hub for SwitchBot sensors, with its own sensor built in, so placed upstairs it doubles as the upstairs reference. SwitchBot’s US Outdoor Meter page says the Hub 2 screen can show that sensor’s readings (a search summary); the US Hub Mini Matter device list omits the Meter series. It needs 2.4 GHz Wi-Fi and USB-C power (5V/2A). On price alone Tapo’s setup costs less, but water resistance and condensation handling are not in the price | Open with these settings |
| Dry room or floor, 1 spot, Add a reference | ✓ Pick: the Tapo sensor and hub setup. 2 sensors (1 spot plus one upstairs reference) and one hub. A Tapo sensor that pairs with the H100 hub. Tapo’s US page for the T315 in the same line lists ±3 %RH accuracy and a required hub. The T310’s own US spec page, its operating range and its water resistance were not checked, so confirm them before using it in a damp spot. On price alone Tapo’s setup costs less, but water resistance and condensation handling are not in the price | Open with these settings |
| Dry room or floor, 2 spots, Add a reference | ✓ Pick: the Tapo sensor and hub setup. 3 sensors (2 spots plus one upstairs reference) and one hub. A Tapo sensor that pairs with the H100 hub. Tapo’s US page for the T315 in the same line lists ±3 %RH accuracy and a required hub. The T310’s own US spec page, its operating range and its water resistance were not checked, so confirm them before using it in a damp spot. On price alone Tapo’s setup costs less, but water resistance and condensation handling are not in the price | Open with these settings |
| Dry room or floor, 3 spots, Add a reference | ✓ Pick: the Tapo sensor and hub setup. 4 sensors (3 spots plus one upstairs reference) and one hub. A Tapo sensor that pairs with the H100 hub. Tapo’s US page for the T315 in the same line lists ±3 %RH accuracy and a required hub. The T310’s own US spec page, its operating range and its water resistance were not checked, so confirm them before using it in a damp spot. On price alone Tapo’s setup costs less, but water resistance and condensation handling are not in the price | Open with these settings |
| May get splashed or damp, 2 spots, No reference | ✓ Pick: the waterproof sensor and hub setup. 2 waterproof sensors (one per spot) and one hub: 2 sensors in all. A thermo-hygrometer SwitchBot lists as waterproof (IP65). That rating covers dust and water jets, not condensation. Its humidity accuracy is ±1.8 %RH, and with a hub you can check it from another floor. A relay hub for SwitchBot sensors, with its own sensor built in, so placed upstairs it doubles as the upstairs reference. SwitchBot’s US Outdoor Meter page says the Hub 2 screen can show that sensor’s readings (a search summary); the US Hub Mini Matter device list omits the Meter series. It needs 2.4 GHz Wi-Fi and USB-C power (5V/2A). On price alone Tapo’s setup costs less, but water resistance and condensation handling are not in the price | Open with these settings |
| Dry room or floor, 2 spots, No reference | ✓ Pick: the Tapo sensor and hub setup. 2 sensors (2 spots) and one hub. A Tapo sensor that pairs with the H100 hub. Tapo’s US page for the T315 in the same line lists ±3 %RH accuracy and a required hub. The T310’s own US spec page, its operating range and its water resistance were not checked, so confirm them before using it in a damp spot. On price alone Tapo’s setup costs less, but water resistance and condensation handling are not in the price | Open with these settings |



